Blue Traxx Forum banner
1 - 20 of 26 Posts

·
Registered
Joined
·
33 Posts
Discussion Starter · #1 ·
If we all List are jet sizes & Exhaust . Then it would be a good refrence.
It would help When We go riding out of state.


I Live in Illinois Elevation 700ft
Im Running A Full Yosha Pipe
170/175
25 Pilots
3 Clip
3 Turn out
No Lid
Pro Flow K/N
Hit 82.6 In -7 Degrees GPS
 

·
Registered
Joined
·
343 Posts
I have a Dr. D slip on

150/155 jets
25 pilot
no lid
and elevation is 1000 ft
2nd clip
 

·
Registered
Joined
·
6,484 Posts
Full Pro Circuit T-4 exhaust
Dynojet stage 2 jetkit
146/148 jets, needle on 3rd notch
3 turns out
modified snorkel per dynojet's instructions
GYT-R air filter adapter with K&N filter and GYT-R "outerwear"
Airbox modified per GYT-R's instructions

1300 feet above seal level
 

·
Premium Member
Joined
·
3,100 Posts
check My sig
I am in Sacramento CA

2 rappies 160/165 25 pilot other 185/190 27.5 pilot
 

·
Registered
Joined
·
124 Posts
FULL CT SONIC KIT, 170/175 JETS, K&N W/ PRO-DESIGN AND NO LID. STOCK PILOTS...3RD CLIP...2 1/2 TURNS OUT...CENTRAL KY...ABOUT 500FT.
 

·
Registered
Joined
·
1,066 Posts
Curtis Sparks X-6(cut to 11 inch)
148/150 Dynojets
3rd clip Needle
Curtis Sparks pilots(dont know what size, came with my pipe)
Prodesign Airfilter adaptor, with K&N
Did not mess with airscrews
Cut up lid, no snorkle
Runs rich in 90's good 50's, and a little lean at 20-30's.
Live in Maryland
 

·
Registered
Joined
·
4,741 Posts
See level and 3,000 ft (runs best at sea level)
Yosh full
No lid
160/165
3rd clip
screws were it ran well
 

·
Registered
Joined
·
156 Posts
Yosh complete, two 1.75 inch holes in lid, 160/165, 25 pilots, needle in stock position, K&N filter and outerwear. (But now I got the Edelbrock with the 21E needle). Oregon coast, and Moses Lake, WA. 0 to 1150 feet.
 

·
Registered
Joined
·
543 Posts
Sparks X6
L&A Adaptor
K&N
Dynojet 165/170 summer (170/175 winter)
Dynojet Needle 3rd clip
27.5 Pilots
2,5 and 3 turns on air screws
5000 ft above sea level.
 

·
Registered
Joined
·
324 Posts
DMC Alien
Sixsixty Adaptor
Dual K&Ns
Dynojet 165/170
Dynojet Needle 3rd clip
25Pilots
2,5 and 2.75 turns on air screws
700 ft above sea level
To keep this post in perspective everyone needs to post what brand of jets and needles they are using
 

·
Registered
Joined
·
537 Posts
Full GYT-R, Carbon Fiber can
Prodesign/Proflow filter and adapter
No Lid
GYT-R 155/160's
GYT-R Needle, Clip in 3rd
GYT-R 27.5 air screws in original place
I'm in Texas, so I have to be AT or NEAR sea level :lol:
and it's ALWAYS humid here!

JBlaze
 
1 - 20 of 26 Posts
Top