Blue Traxx Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 66 Results
  1. Yamaha YFM350 Raptor/Warrior ('87-Present)
    So I bought the bike about 3 weeks ago. I got it running after sitting for 6 years what a surprise. Replaced the pedcock, fuel line, and inline fuel filter, and took the carb apart to clean it. The jet was all gummed up cleaned that out and cleaned the bowl and everything. Put it all back...
  2. Yamaha YFM350 Raptor/Warrior ('87-Present)
    So I have an 01 and the electric start doesn’t work anymore it would crank and crank but never start but that’s not the real issue. I’ve always been able to bump start it just fine and once it’s started it ran great until one day I was trail riding and out of nowhere it just died on me and so I...
  3. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Hey everyone, I’m working in a 94 warrior engine. I split the case and went through the motor, only thing I didn’t pull was the crank, as I was going to join the case halves together, what I believe to be a needle from a bearing fell out. I have looked at every parts diagram and cannot figure...
  4. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I have a 2000 Yamaha Warrior 350, and it has a FMF Megamax 2 slip on exhaust on it. I bought it from the previous owner like this. I do not have the stock exhaust. I was wondering if anyone knew any semi-inexpensive ways to make it quieter. It has a nice low sound, but it is a bit loud for my...
  5. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Got a 97 warrior 350 with a Chinese top end kit the rings went so I decided to buy a wiesco topend kit and don’t know the ring gap was wondering if anyone could help me.
  6. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I bought a 1997 Yamaha Warrior 350 a couple weeks ago for a good deal, it didn’t run but the owner said it was probably the timing chain and tensioners, he said he heard the chain slapping when it ran. I’ve replaced one of the guides and tensioners, which tightened the chain back up, but the...
  7. Yamaha YFM350 Raptor/Warrior ('87-Present)
    2001 warrior 350 only turns over for half a second as soon as i put the key position to on, If i turn it on and wait more then 2 seconds to click the electric start button it won’t even turn over at all… Anybody know what this could be?
  8. Tires & Wheels
    I was wondering if anyone knows if another manufacturer makes wheels that are the same bolt pattern as a Yamaha Warrior (2001) and a 700 Raptor (2020)? I have been searching for paddle tires (Sand Tires) with wheels for a trip to Silver Lake Michigan soon. My Warrior and Raptor have the same 9...
  9. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I have a 2001 yamaha warrior 350 and I blew out the carrier bearings so I tried swaoing the one I have out of a parts warrior. That didn't fit right the bolt holes were a couple millimeters off. So I ordered the exact oem fit niche carrier and that's the same way. The one that was in it has...
  10. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I just bought a warrior and want to put extended a-arms on it and want to know if aftermarket banshee a-arms will fit, thanks. It is a 1988
  11. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I just replaced the timing chain on my 350 warrior due to the loud slapping noise I was hearing. Chain was defiantly worn. I put the new one in and it runs great, however I am now hearing a clicking or snapping noise coming from the area around the fly wheel cover. I am fairly certain it is not...
  12. ATV Media
    Is the hub that holds on the disk for the back brake interchangeable on the 350 warrior and 350 raptor? I keep seeing that the raptor axle won't work on the warrior.that's why I'm trying to figure out if just the bracket is interchangeable..
  13. Yamaha YFM350 Raptor/Warrior ('87-Present)
    So I went to check my valves the other day because they sounded like they needed adjusting and the intake valves locking nut was no where to be found mind you I know I put one on it.... the only place it could go is down into the case right??? Flash forward I’m out riding and I’m in 3rd and I...
  14. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I have a 1987 Yamaha warrior 350. I got it from a friend, he blew it up. I dropped a new bottom and and top and into it. It seems as though it is stuck in reverse. The reverse selector shaft does not turn enough to go into drive. The reverse light is not on and I have no spark. Wether or not the...
  15. Yamaha YFM350 Raptor/Warrior ('87-Present)
    My bike is a wiring nightmare, everything is just spliced together and nuts. But it does start and run half decent off this wiring, my problem is trying to figure out how many fuses the bike actually needs because I have only found one in the front of the bike for the lights. Also oil leaks a...
  16. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Hello I'm new to these forms but when ever I need to know something I would Google it and you guys came up. But anyways I have a warrior 350 2000 and I noticed I have a head gasket leak from oil smoking coming out of the head so I went to go change the head gasket I put the engine to top dead...
  17. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I replaced the one way bearing behind the flywheel with a new one, on reinstall it just spins as it did before. The quad is leaning over on its side, will that affect anything? Does that bearing need to be wet?
  18. New Members Introductions
    I replaced the one way bearing behind the flywheel with a new one, on reinstall it just spins as it did before. The quad is leaning over on its side, will that affect anything? Does that bearing need to be wet?
  19. Yamaha YFM350 Raptor/Warrior ('87-Present)
    I was working on a friends 85 Warrior. After many hours we got the carb rebuilt and she started right up. Little did I know there was not a drop of oil in it. Ran for about 2 miles and it crapped out. You can get compression by spinning the motor by hand but when you try to electric start it it...
1-20 of 66 Results
Top