Blue Traxx Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. Yamaha YFM660R Raptor (2001-2005)
    Recently changed my clutch plates on a 2003 raptor. Changed oil and coolant during the replacement. Started up great, double checked all fluid levels during starting, warmup and shutdown. Added fluid as needed till all fluids measured full. Took the bike for a quick ride down the street and...
  2. Yamaha YFM660R Raptor (2001-2005)
    So I changed the clutch in my 04 Raptor 660, went to take it for a test ride and realized it wont shift, took it for a ride and still wont shift from first. I didn't pull the basket. I also marked the arrow on pressure plate and the punch mark and pretty sure I got that right. What else is...
  3. Yamaha YFM660R Raptor (2001-2005)
    Hey all, I'm new to this site and also new to quads. I recently got my first quad a week ago 04 raptor 660, anyways I smoked the clutch the second day. I got the parts now and I got the case off and I'm down to my clutch.. MY Question is, is the center shaft that goes through the pressure plate...
  4. ATV Parts & Accessories Classifieds
    New ASV C6 Brake Lever - $95.00 obo Pro Clutch perch - $45.00 obo Dust boot - $10.00
  5. Yamaha YFM350 Raptor/Warrior ('87-Present)
    My warrior seems to be slipping in all gears mainly 2nd through 6th when i really have the throttle open. But then if i ease it into the the gear its fine.. Is it the clutch/clutch plates going bad?
  6. Yamaha YFS200 Blaster ('88-Present)
    Could the clutch springs being too loose cause the inner clutch basket boss to break? Or cause the clutch not to engage at all? New rebuild and the clymers manuel is not specific enough. " Install" is not thorough enough for me... Thanks!
  7. Yamaha YFS200 Blaster ('88-Present)
    Ok, so I just "finished" rebuilding a 2000 blaster. Had to replace entire trans due to 1st gear being in 4 pieces. Now I can't get it to engage gears. Trans went in smooth with full operation even after cases were resealed and all gears installed. Clutch issue? Shift drum in wrong? (forks are...
  8. Yamaha YFM660R Raptor (2001-2005)
    So long story short is i started tearing in to a 660 motor before i really knew what was wrong with it the boy told me that the crank was locked up but i got the side case off where the one way is at and i found on craigslist the same fourwheeler and he said on there the one way was bad and i...
  9. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Today i got new hand grips for my 03 yamaha warrior and i put them on and there was a big gap between my grips and the thing that has the heads lights and start button on it. So i loosened that and slid it over until it touched the hand grips and then i pulled the clutch lever and it was hiting...
  10. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Hey everyone I'm new here and am having some problems with my quad. I just redid all this cosmetic work on a 2000 350 warrior. New plastics, lights, pipe, seat, grab bar, etc. Also put on a new clutch cover and shift lever. It ran great and one day went out to start it and once it ran for...
  11. ATV Parts & Accessories Classifieds
    Like the title says, brand new parts and never got to put them on. Kid broke BOTH his arms and now he's hollering bout not ever wanting to ride again. Now I got a bunch of boxes of stuff for this damn atv that aint ever going to ever get used. The four wheeler is a '07 YFZ 450SE Parts...
  12. Other Models/Brands
    Hey guys. I'm hoping someone has some clue what's going on with my ride. I bought a 2001 wolverine (yfm350fxn) for cheap because it was in pieces. Oil pump was toast, and this toasted the cam. I replaced/rebuilt, seems to run fine now, except I get a high pitched whine when in higher gears...
  13. Other Models/Brands
    I just purchased a 1996 Kodiak 400 4X4. Knowing little about these (I have a motorcycle background), I believe I may have a clutch issue. First, this one has the 5 speed manual shift (clutchless) tranny. When you accelerate from a stop, the engine winds up for a few seconds, then...
  14. Yamaha YFM350 Raptor/Warrior ('87-Present)
    Ok I need to change the starter clucth on my warrior it's a 1988 and I know how to do it but wen it comes to taking off the flywheel do I undo the Alen key bolts around the inside of the fly wheel or do I just pull it off cause I was told just pull it but I'm not sure and if anybody can help or...
1-14 of 14 Results
Top